|
About the Modules & Chipsets category
|
|
1
|
620
|
July 19, 2017
|
|
Prototyping with SCM20100E
|
|
15
|
241
|
October 6, 2020
|
|
Differences between SCM-20260N-B and SCM-20260N-C
|
|
10
|
140
|
October 2, 2020
|
|
Which BLE click?
|
|
5
|
85
|
September 23, 2020
|
|
SITCore eagle library
|
|
2
|
99
|
September 22, 2020
|
|
Bluetooth for SITcore. Which module?
|
|
8
|
189
|
August 29, 2020
|
|
GPIO input SC20100 PE0 / pin 97 not working
|
|
10
|
191
|
July 9, 2020
|
|
Troubleshooting SC20100S issue... voltage low on 3.3v bus
|
|
7
|
128
|
July 7, 2020
|
|
SC20260D Dev Board Model?
|
|
2
|
157
|
May 27, 2020
|
|
Updates on SC20100S TQFP SOC availability?
|
|
4
|
138
|
May 15, 2020
|
|
Mouser starting to show SITcore
|
|
1
|
139
|
May 11, 2020
|
|
SC20100 pins?
|
|
9
|
211
|
May 7, 2020
|
|
Look what is getting built right now, SCM20100E
|
|
6
|
270
|
May 7, 2020
|
|
Did wifi go away?
|
|
6
|
251
|
May 4, 2020
|
|
How small is this new SoM?
|
|
15
|
301
|
May 1, 2020
|
|
SCM20260N availability?
|
|
10
|
382
|
April 30, 2020
|
|
SC20260E module
|
|
1
|
190
|
April 17, 2020
|
|
Marginal timing issue with MassStorage on G120
|
|
6
|
220
|
April 7, 2020
|
|
Planning for G120B and G400D Obsolescence
|
|
2
|
282
|
February 5, 2020
|
|
Upgrade path clarification
|
|
26
|
254
|
December 10, 2019
|
|
Wiring for UCM Breakout Board + G400-D
|
|
6
|
396
|
September 28, 2019
|
|
Current GHI products power consumption
|
|
7
|
720
|
August 23, 2019
|
|
Cannot load the Firmware on the G120E
|
|
5
|
290
|
April 15, 2019
|
|
7 inch display: Which UCM module?
|
|
9
|
361
|
March 11, 2019
|
|
Any new SoM plans?
|
|
4
|
326
|
January 25, 2019
|
|
G400S problems update samba bootloader
|
|
17
|
515
|
January 23, 2019
|
|
UCM Development Board - Dissapointed that Mode signal circuit was changed
|
|
4
|
480
|
October 26, 2018
|
|
UCM Breakout board ... not very impressed!
|
|
13
|
1102
|
October 18, 2018
|
|
Mechanical Drawing for UCM Development Board
|
|
12
|
995
|
September 17, 2018
|
|
Cobra III - logging CAN to USB
|
|
12
|
714
|
July 22, 2018
|
